How to Apply the Death Stranding United Cities Patch to Jackets
By Kojima Productions | Published: 2026-10-15
Category: How-to Guides
A step-by-step guide to placing and attaching the DEATH STRANDING United Cities Removable Patch on denim, canvas, and zip jackets, plus the mistakes that cause peeling or crooked placement.
Quick answer
Place the DEATH STRANDING United Cities Removable Patch on a flat, low-flex zone such as an upper sleeve, chest panel, or back yoke, then attach it according to the removable backing rather than defaulting to a hot iron. Because the patch is designed to be removable, treat heat and adhesive as optional and test on an inside seam first. If you want a permanent look, stitch the edges after positioning rather than pressing hard.
Choose a jacket zone that suits a removable patch
Removable patches work best where the fabric stays flat and does not crease constantly. On a denim or canvas jacket, the upper sleeve, chest panel, and back yoke are reliable. Avoid elbows, side seams, and anywhere a backpack strap or seatbelt rubs, because friction is what lifts a removable patch edge first.
If your jacket has a zip hoodie build, the fabric is softer and stretches more, so keep the patch smaller in placement footprint and center it on a panel instead of crossing a seam. Seams create ridges that stop the backing from sitting flush.
Match the backing to the fabric before you attach anything
The catalog does not list a specific adhesive type or iron temperature for this patch, so do not guess a heat setting. Check the backing you receive and follow its instructions. As a general checkpoint, test any heat method on an inside hem first, and never iron directly over the patch face, because logos can scorch or shine.
For a removable patch jacket setup, a low-tack or hook-and-loop style backing lets you reposition without residue. If the backing is heat-activated and you want to keep it removable, use the lowest effective heat and short presses rather than a long hold.
Position with a dry run before committing
Put the jacket on a hanger or flat surface, place the patch, and step back two paces. Check that the logo reads straight relative to the jacket, not relative to the floor, because jackets hang at an angle. Mark the corners with removable tape or pins so the patch cannot shift while you attach it.
Patch placement tips that hold up: keep at least 2 cm of clear fabric around the patch edge, align the top edge with an existing seam if one is nearby, and avoid placing it where a bag strap will cross it.
Step-by-step: applying the patch
- 1. Prep the jacket surface: Lay the jacket flat or hang it, brush away lint, and smooth the fabric. Check that the target zone is not wrinkled. Common mistake: attaching over a wrinkle, which traps a fold under the patch and causes a lifted edge later.
- 2. Dry-fit and mark the position: Place the patch, step back to check alignment, then tape or pin the corners so it cannot shift. Checkpoint: the logo should look straight when the jacket is worn, not just when it is flat on a table.
- 3. Test the backing on an inside seam: If you plan to use heat, press a small hidden area first to see how the fabric reacts before touching the patch. Common mistake: ironing the patch face directly, which can scorch or polish the logo.
- 4. Attach with light, even pressure: Follow the backing instructions, working from the center outward so no air pockets remain under the patch. Checkpoint: press for the shortest time that holds, especially if you want to keep the patch removable.
- 5. Cool, then check the edges: Let the jacket cool completely before wearing or flexing it, then run a finger around the border to feel for lifting. Common mistake: wearing the jacket immediately, which stretches warm adhesive and shortens the patch's life.
- 6. Reinforce or remove as needed: If you want a permanent look, add a few stitches at the corners. If you want to move it, peel slowly from one corner rather than pulling straight off. Next step: store the patch flat between wears so the backing stays clean for reuse.
Product facts
- DEATH STRANDING United Cities Removable Patch: Officially branded Kojima Productions accessory featuring the UNITED CITIES logo from DEATH STRANDING, with a removable patch design. The removable design means you can reposition it between jackets instead of committing to one placement, which is ideal if you are still testing patch placement tips.
- DEATH STRANDING BB Sleeping T-Shirt: DEATH STRANDING BB Sleeping T-Shirt with a BB sleeping in the pod print, available in black, white, and navy, with sizes Small through XX-Large (availability varies by color). A clean printed tee gives the patch a flat, low-friction surface, so it can be a lower-risk first test before you attach the patch to a heavier jacket.
